News

1) moves the table or spindle, according to the workpiece is much closer, correct selected speed, to prevent collision when moving too fast. 2) To determine the correct programming and machining process route based on the actual situation, to prevent the workpiece machining position due to lack of insufficient strength or take the side caused by retirement or early fall off. 3) must be confirmed before the line cut program and the amount of compensation is correct. 4) Check the wire tension is adequate. When cutting taper tension should be adjusted down to the usual half. 5) Check the electrode wire feed speed is appropriate. 6) Choose open or close the machining process according to the actual situation to be processed, in the premise of avoiding interference to shorten the distance between the nozzle and the workpiece. Adhesion process, the distance between the nozzle and the workpiece generally take 0.05 ~ 0.1mm. 7) Check the jet stream selection is reasonable, with a high pressure jet roughing, finishing with a low pressure jet. 8) should be cut from the judge to observe the processing stability, timely adjustment bad when found. 9) process, should regularly inspect and supervise the cutting conditions, we found the problem immediately.

Nail gun use fastener installation in strip (similar to nail a bar) or in paper or plastic carrier, depending on the design of the nail gun. Some with nail gun, especially those used for tray manufacturing and roof, use long plastic or metal wire coil. Some take nailing machine cutting head, the nails can be closely together, making it less frequent heavy. Nail clip is by the state or local building codes, sometimes is prohibited. All round head nail nails and ring provides greater resistance to pull out. Nailing machine also can be a "coil" type, including fasteners in metal wire or plastic check; Its advantage is many, each load multiple fasteners, but at the expense of extra weight. Industrial nail gun is designed for use of steel or concrete can be for explosive loading cap, but the most need to nail loading by hand. Nail gun in nail they can drive the length and gauge (thickness). Nail gun Usage The minimum size of the fastener 23 is usually measured diameter (0.025 inches), commonly referred to as "pin experts" and generally do not have heads. They are used to from curling, mold, and so the furniture has been to medium (7-8 inches) baseboards, crown molding and casing. Length typically 1¼⅜ range. (10--32 mm) although some industrial tool manufacturers supply 2. (50 mm). The 23rd Regulation microneedles rapid progress, because users find it leaves a much smaller Bibulade nail holes, thereby eliminating the time usually taken to fill and provide better products. The next size is 18 gauge (1.02 mm diameter) is fixed, often referred to as a "brad nail." These fasteners are used to repair the mold but can be used in the same way Subtotal fastener 22 to 24 days. Their greater strength led them to cut hardwood woodworking some holes to fill are acceptable. Most 18 measuring angle nailhead, but some manufacturers offer headless fasteners. Length ranges from ⅝2. (16 mm to 50 mm) The next size is 16--15 meter (1.63 and 1.83 mm diameter). These are often referred to as "complete nail." They come in lengths between ⅝ and 2½. 64 mm (16) and for the repair of softwood and MDF pruning work (such as baseboard / skirtings, architraves, etc.) of holes after work and painting. The maximum size of a conventional fastener is finishing nail scissors head and full head for the frame, fencing and other forms of structure and exterior work. These nails are generally shank diameter 0.11 to 0.13. (2.9 to 3.1 mm), although some manufacturers offer smaller diameter nail. General length of 23 1/3 (50--90 mm). Ring handle styles include plain, ring, twisted, etc., and a variety of materials and completed including the provision of ordinary steel, galvanized steel, sherardised steel, stainless steel, etc. depending on the pullout resistance, corrosion resistance, etc. required for a particular application. These dimensions adhering to organize the formation of fasteners (usually 20 ° 21 ° full head, cutting head 28 ° 34 °) or coil form (for pallet / roofing expert) depends on the application. Full head nails with greater pullout strength than nails and a lot of structure in the framework of the provisions of the code hurricane zone. Another type of construction is belt tightening, roughly analogous to the large stud fastening common influence. These experts use a gun (or positive placement experts Kingdom) repair of metal products such as joist hangers, angle board, wood and other structural reinforcement straps binding. They are experts with traditional fastening purpose is not the package, so it can accurately locate prelaunch nail. https://en.wikipedia.org/wiki/Nail_gun

What is the purpose of an intercooler in an air compressor? Intercoolers lower the temperature of air going from one stage of a compressor to another, it increases the efficiency as the air becomes more dense. As the recieving stage is compressing cooler air as result, there is less heat produced in the succeding stage. If the intercooler has a large surface area, the temperature can approach ambient temperatures, and moisture my drop out, requiring a method for it's removal; if not a slug of water could damage the recieving stage. Efficiency increases can be had >15% . Why use an air compressor regulator? use air regulator to stop motor so it don't over fill tank, tank could explode if over fill pass it's rating. What parts does a air compressor consist of? In general an air compressor is made up of three parts. They are the air pump, the motor and the tank that holds the compressed air. How do you calculate air compressor capacity? Flow rate times pressure divided by input will yield air compressor capacity. Input is another term for horsepower of the compressor. The pressure can be adjusted depending on how compact the result is to be. http://www.answers.com/Q/What_is_the_purpose_of_an_intercooler_in_an_air_compressor